--------------------------------------------------------------------
-- The ATM Service Registry MIB for Network Management.
--
-- March 1996, Kartik Chandrasekhar
--
-- Copyright (c) 1996-1997 by cisco Systems, Inc.
-- All rights reserved.
--------------------------------------------------------------------CISCO-ATM-SERVICE-REGISTRY-MIB DEFINITIONS::=BEGINIMPORTSMODULE-IDENTITY,OBJECT-TYPE,Integer32FROM SNMPv2-SMI
TEXTUAL-CONVENTION,RowStatusFROM SNMPv2-TC
MODULE-COMPLIANCE,OBJECT-GROUPFROM SNMPv2-CONF
ciscoMgmt FROM CISCO-SMI;
ciscoAtmServiceRegistryMIB MODULE-IDENTITYLAST-UPDATED"9602210000Z"ORGANIZATION"Cisco Systems, Inc."CONTACT-INFO" Cisco Systems
Customer Service
Postal: 170 W. Tasman Drive
San Jose, CA 95134-1706
USA
Tel: +1 800 553-NETS
E-mail: cs-snmp@cisco.com"DESCRIPTION"A MIB module to allow an NMS to monitor and
configure the information which an ATM switch
makes available via the ILMI's Service Registry
Table."REVISION"9602040000Z"DESCRIPTION"Initial version of this MIB module."::={ ciscoMgmt 50}ciscoAtmServiceRegistryMIBObjects
OBJECTIDENTIFIER::={ ciscoAtmServiceRegistryMIB 1}-- AtmAddr defined here for completeness. Over time it should be
-- imported from the ATMTC-MIB under development by the IETFAtmAddr::=TEXTUAL-CONVENTIONSTATUScurrentDESCRIPTION
"The ATM address used by the network entity. The
address types are: no address (0 octets), E.164 (8
octets), network prefix (13 octets), and NSAP (20
octets). Note: The E.164 address is encoded in
BCD format."SYNTAXOCTETSTRING(SIZE(0|8|13|20))InterfaceIndexOrZero::=TEXTUAL-CONVENTIONDISPLAY-HINT"d"STATUScurrentDESCRIPTION"Either the value 0, or the ifIndex value of an
ATM Interface."SYNTAXInteger32(0..2147483647)-- The Service Registry Table
--
-- The Service Registry Table is implemented by ATM switchesasrSrvcRegTable OBJECT-TYPESYNTAXSEQUENCEOF AsrSrvcRegEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The table implemented by an ATM switch to allow
monitoring and control of the ATM addresses of
registered services which it makes avaiable to ATM
end-systems via the ILMI across its UNIs."::={ ciscoAtmServiceRegistryMIBObjects 1}asrSrvcRegEntry OBJECT-TYPESYNTAX AsrSrvcRegEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Information about a single service provider that is
to be made available to the user-side of one or more
ATM UNIs. An entry, for which asrSrvcRegPort has a
non-zero value, is a specific assignment to that UNI;
an entry for which asrSrvcRegPort is zero applies to
all UNIs for which this table contains no specific
assignments."INDEX{ asrSrvcRegPort, asrSrvcRegServiceID,
asrSrvcRegAddressIndex }::={ asrSrvcRegTable 1}
AsrSrvcRegEntry ::=SEQUENCE{
asrSrvcRegPort InterfaceIndexOrZero,
asrSrvcRegServiceID OBJECTIDENTIFIER,
asrSrvcRegATMAddress AtmAddr,
asrSrvcRegAddressIndex Integer32,
asrSrvcRegParm1 OCTETSTRING,
asrSrvcRegRowStatus RowStatus}asrSrvcRegPort OBJECT-TYPESYNTAXInterfaceIndexOrZeroMAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Either the value 0, or the ifIndex value of an
the ATM Interface. A row for which this object has a
non-zero value is a specific assignment to that UNI;
a row for which this object is zero applies to
all UNIs for which this table contains no specific
assignments.
Some switches may only support this object with the
value of zero."::={ asrSrvcRegEntry 1}asrSrvcRegServiceID OBJECT-TYPESYNTAXOBJECTIDENTIFIERMAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The service identifier which uniquely identifies
the type of service at the address given by the
corresponding value of asrSrvcRegATMAddress.
Specific values for this identifier are defined in
the ILMI specification (e.g., asrSrvcRegLecs) or
elsewhere."::={ asrSrvcRegEntry 2}asrSrvcRegATMAddress OBJECT-TYPESYNTAXAtmAddrMAX-ACCESSread-createSTATUScurrentDESCRIPTION"An ATM address to which the ATM end-system on this
UNI can attempt to establish a connection for the
service."::={ asrSrvcRegEntry 3}asrSrvcRegAddressIndex OBJECT-TYPESYNTAXInteger32MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An arbitrary integer to differentiate multiple rows
containing different ATM addresses for the same service
on the same UNI."::={ asrSrvcRegEntry 4}asrSrvcRegParm1 OBJECT-TYPESYNTAXOCTETSTRINGMAX-ACCESSread-createSTATUScurrentDESCRIPTION"An octet string used according to the value of
asrSrvcRegServiceID."::={ asrSrvcRegEntry 5}asrSrvcRegRowStatus OBJECT-TYPESYNTAXRowStatusMAX-ACCESSread-createSTATUScurrentDESCRIPTION"The status of this row. No object in the row can
be modified while the value of this object is
'active'."::={ asrSrvcRegEntry 6}-- conformance informationasrSrvcRegMIBConformance OBJECTIDENTIFIER::={ ciscoAtmServiceRegistryMIB 3}asrSrvcRegMIBCompliances OBJECTIDENTIFIER::={ asrSrvcRegMIBConformance 1}asrSrvcRegMIBGroups OBJECTIDENTIFIER::={ asrSrvcRegMIBConformance 2}-- compliance statementasrSrvcRegMIBCompliance MODULE-COMPLIANCESTATUScurrentDESCRIPTION"The compliance statement for ATM switches which
implement the Cisco Service Registry MIB"MODULE-- this moduleMANDATORY-GROUPS{ asrSrvcRegMIBGroup }::={ asrSrvcRegMIBCompliances 1}-- units of conformanceasrSrvcRegMIBGroup OBJECT-GROUPOBJECTS{
asrSrvcRegATMAddress,
asrSrvcRegParm1,
asrSrvcRegRowStatus
}STATUScurrentDESCRIPTION"A collection of objects providing monitoring and
control of ATM addresses of services which an ATM
switch is to make available via the ILMI."::={ asrSrvcRegMIBGroups 1}END